To enter the code, press the p key on the right side of the keypad. Enter a five-digit code when prompted to configure the operating system of the safe. Take out your mobile device, launch the QR code reader application, and start scanning. The sticker on the right can be removed by prying it off with a flathead screwdriver, then peeling it off with tweezers so it remains intact. You cannot scan it with your phone due to the angle. Once outside, we must locate a solenoid and a secret bar code in the upper-right corner. When you open the door and examine the left side of the panel inside, you will notice three tiny notches that accommodate a flat-bladed screwdriver. What should we do if we have forgotten our sentry safe’s factory code and need to reset it? To reset it, you need a flathead screwdriver, pliers, and a smartphone capable of reading a QR code or barcode.Įnter a new password to unlock the safe door quickly. Overall, you should allot seven to ten days for the procedure. In this scenario, a notarized letter proving safe ownership is required. You may still receive your combination code even if you still need to sign up for the Sentry Safe website. You can quickly access the recorded code for your combination lock by clicking this link. ![]() Use your username and password to access the website combination you just created. You can also look up serial and model numbers for Safe Sentry products. The model and serial numbers of your product will be required. The second step is to input some information that verifies your ownership of a Sentry Safe. Look for a Lost Key or Combination Support page on the Sentry Safe website. Recovery of forgotten Sentry safe password Enter the five-digit code from your application and wait for the one-beep signal from the database before entering the new code. To input, the code, hit the p key on the right side of the keypad. ![]() Take out your mobile device, activate your QR code reader, and start scanning! Use the displayed five-digit code to configure your safe’s software. To remove the sticker on the right, pry it up from where you affixed it with a flathead screwdriver, and then remove it with tweezers without tearing it. When we reach the outdoors, we must locate a solenoid and a bar code in the upper right corner.ĭue to the angle, you won’t be able to use your phone’s scanner. When the door is open, check for three small notches that can be accessible with a flathead screwdriver on the left side of the interior panel. ![]() That is all it takes to alter the safe’s door code. To reset it, you’ll need a flathead screwdriver, pliers, and a smartphone with QR code or barcode scanning capabilities. You will need the original manufacturing code to reset the combination on your sentry safe. If your Sentry safe is older, press PROG twice and enter the factory code by entering factory code. After entering the factory code, press the “00000” button to open the safe. On more recent safe models, pressing the P button will delete all previously entered codes when pressed. This factory-determined code is immutable. You must open the Sentry safe’s door with the five-digit factory code found in the user manual. To avoid being locked out of a Sentry safe, it is always prudent to reset the combination before gaining access. The final step is to enter a new user combination consisting of a user-selected five-digit number. To reset the combination, open the Sentry safe’s door, press the PROG or P key, and enter the factory code. While the green light to proceed is on, we will use 1, 2, 3, 4, and 5. Unique to you, enter a five-digit primary user code. The safe’s combination is 8 2 5 1 9, and the green proceeds light is on. Enter the five-digit factory code on the keypad by pressing the program button. Ensure that your safe’s door is open before programming a five-digit primary user code. The five-digit factory code is located on the manual’s back cover. Use a Sentry Safe reset tool.įind the user’s manual. The time limit for entering your primary user code is strictly 5 seconds. To reset the user code on your Sentry Safe DH-074E, press the program (P) button and enter the factory code on the electronic keypad.Īfter the green light blinks, enter a unique five-digit primary user code. The caution will be displayed above the username field. ![]() If you enter the correct combination, a red warning message will display. You can recover your username and password if you are confident that you entered them correctly. You will enter your username and password in the “Find a Registered Combination Online” field on the website.
0 Comments
Leave a Reply. |